Getting Started: Difference between revisions

From AnalysIR WiKi
Jump to navigation Jump to search
Line 16: Line 16:
== Default KontroLIR Firmware ==
== Default KontroLIR Firmware ==
We provide a fully functional firmware  for 5 example devices, which uses only a small amount of FLASH and SRAM.
We provide a fully functional firmware  for 5 example devices, which uses only a small amount of FLASH and SRAM.
* Device Mode 1 - is a philips smart TV with a mic of RC5 and RC6 protocols ''(Press TV button to enter Mode 1, from all modes)''
* Device Mode 1 - is a Philips smart TV with a mix of RC5 and RC6 protocols ''(Press TV button to enter Mode 1, from all modes)''
* Device Mode 2 - is satellite STB, which mainly uses the NEC protocol ''(press SAT button to enter Mode 2, from Modes 1,3,4 or 5)''
* Device Mode 2 - is a generic satellite STB, which mainly uses the NEC protocol ''(press SAT button to enter Mode 2, from Modes 1,3,4 or 5)''
* Device Mode 3 - is for a Samsung TV, which uses teh Samsing Protocol ''(press DVD button to enter Mode 3, from Modes 1,2,4 or 5)''
* Device Mode 3 - is for a Samsung smart TV, which uses the Samsung Protocol ''(press DVD button to enter Mode 3, from Modes 1,2,4 or 5)''
* Device Mode 4 - implements a Microsoft Media Center remote control using an extended RC6 protocol. ''(press SAT button to enter Mode 4, from Mode 2 only)''
* Device Mode 4 - implements a Microsoft Media Center remote control using an extended RC6 protocol. ''(press SAT button to enter Mode 4, from Mode 2 only)''
* Device Mode 5 - implements a series of test signals, usedd for testing KontroLIR. ''(press DVD button to enter Mode 5, from Mode 2 only)''
* Device Mode 5 - implements a series of test signals, used for testing KontroLIR. ''(press DVD button to enter Mode 5, from Mode 2 only)''
* If the user is uncertain of the current mode, they can press TV to get back to the default Mode 1 and proceed to other modes as required.
* If the user is uncertain of the current mode, they can press TV to get back to the default Mode 1 and proceed to other modes as required from there.
* It is always possible to extend the number of modes, by using oher buttons or sequences for this purpose.
* It is always possible to extend the number of modes, by using oher buttons or sequences for this purpose.
* Converseley, if the user requires less modes you can convert the 3 device buttons into signal buttons as required.






'''''[[KontroLIR - Arduino compatible IR remote control|> KontroLIR Home]]'''''
'''''[[KontroLIR - Arduino compatible IR remote control|> KontroLIR Home]]'''''

Revision as of 07:47, 6 October 2019

> KontroLIR Home

Follow this section the first time you get your KontroLIR remote control.


Checklist

  • Make sure you have s SerialUSB adapter which has a pinout for Vcc, GND, Tx, Rx and either DTR or RTS. (Note: some adapters do not have the DTR/RTS pin available, which is required for uploading firmware using the Arduino IDE)
  • Make sure you have a USB cable to use with the serialUSB adapter.
  • Double check your order to establish if you have one or more of the options (EEPROM or dual IR Receivers)
  • If you ordered the SerialUSB adpater, then it will be compatible with KontroLIR.
  • For CP2101 based SerialUSB adapters, drivers can be downloaded from CP2102 Driver download
  • For initial usage, it is best to power KontroLIr with the SerialUSB adapter, until you are ready to use with batteries.
  • Make sure to have 2xAAA batteries availble befor you plan to start using KontroLIR as a remote.
  • Advanced users can also make use of the internally accessible ICSP compatible programming header to upload firmware with or without a bootloader and change fuse settings. However, frequently opening the enclosure could cause some issues over time if care is not taken. We use spludgers and lots of TLC when opening the enclosure to avoid potetial for damage.

Default KontroLIR Firmware

We provide a fully functional firmware for 5 example devices, which uses only a small amount of FLASH and SRAM.

  • Device Mode 1 - is a Philips smart TV with a mix of RC5 and RC6 protocols (Press TV button to enter Mode 1, from all modes)
  • Device Mode 2 - is a generic satellite STB, which mainly uses the NEC protocol (press SAT button to enter Mode 2, from Modes 1,3,4 or 5)
  • Device Mode 3 - is for a Samsung smart TV, which uses the Samsung Protocol (press DVD button to enter Mode 3, from Modes 1,2,4 or 5)
  • Device Mode 4 - implements a Microsoft Media Center remote control using an extended RC6 protocol. (press SAT button to enter Mode 4, from Mode 2 only)
  • Device Mode 5 - implements a series of test signals, used for testing KontroLIR. (press DVD button to enter Mode 5, from Mode 2 only)
  • If the user is uncertain of the current mode, they can press TV to get back to the default Mode 1 and proceed to other modes as required from there.
  • It is always possible to extend the number of modes, by using oher buttons or sequences for this purpose.
  • Converseley, if the user requires less modes you can convert the 3 device buttons into signal buttons as required.


> KontroLIR Home