Search results
Jump to navigation
Jump to search
- ...strates how to write data to EEPROM, erase pages and verify written pages. Users should be able to re-use this code to implement their own requirements. ...2 KB (339 words) - 11:06, 10 December 2019
- Just go to C:\Users\'''USERNAME'''\AppData\Roaming\LearnIR\KeySets ...574 bytes (104 words) - 06:56, 10 January 2024
- Just go to C:\Users\'''USERNAME'''\AppData\Roaming\LearnIR\KeySets ...575 bytes (104 words) - 06:54, 10 January 2024
- Most users, should leave all of the low power operations as is. Any future improvement Advanced users can try to implement even lower power operation and are welcome to contribu ...2 KB (374 words) - 08:48, 10 December 2019
- ...d signal sequences in this file, but have left them commented-out for now. Users are free to add any number of macros here. We strongly suggest you use this ...1 KB (191 words) - 12:50, 10 December 2019
- Advanced users may try using the 8Mhz clock rate or when powered from USB during testing. ...1 KB (239 words) - 13:50, 27 January 2020
- There are additional headers available for advanced users, as follows: Advanced users, may further expand KontroLIR, using the following GPIOs, if available. ...4 KB (645 words) - 08:46, 11 December 2019
- ...fault is 2. A higher value should increase battery life somewhat for heavy users. ...2 KB (304 words) - 09:41, 9 October 2019
- * Experienced users will be able to run from other locations and force running in the backgroun ...mand: '''''python servAIR.py 9449 &'''''. Depending on configuration, some users may need to type '''''sudo python servAIR.py 9449 &'''''. ...9 KB (1,385 words) - 06:26, 17 February 2020
- Once installed the library folders can typically be found in C:\Users\'''[USER]'''\Documents\Arduino\libraries\IRremote\ where '''[USER]''' is yo ...2 KB (376 words) - 05:53, 20 July 2021
- ...s pressed in MODE2 then MODE4 is set and pressing DVD in MODE3 sets MODE5. Users can extend this logic further as desired and use other buttons to set modes ...he new mode entered when one of the mode buttons are pressed in each mode. Users are free to extend this as required using any buttons or combinations. ...5 KB (832 words) - 08:13, 11 December 2019
- The enclosure of KontroLIR is '''not designed for opening''' by users, other than for replacing batteries and uploading firmware via the battery Advanced users may decide to go ahead and open the enclosure, to gain access to the ICSP p ...6 KB (967 words) - 08:24, 7 September 2021
- ...ton was pressed we assume the first one found is the one that was pressed. Users could extend this logic to support multiple key presses etc. ...4 KB (673 words) - 04:47, 11 November 2019
- ...ignores other buttons when multiple buttons have been pressed together. ''(Users could extend the logic to support multiple simultaneous button presses if d ...5 KB (854 words) - 10:15, 10 December 2019
- ...dule as part of a soldering class or course under supervision. Experienced users can use the kit to complete their own high-end IR module. ...6 KB (1,005 words) - 11:07, 19 September 2018
- ...h. If neither jumper is inserted then there will be no IR emitted. ''(Some users may want to leverage this to use a relay or mechanical switch to allow cont ...7 KB (1,337 words) - 17:17, 12 March 2019
- ''R1 is not included in the kit and is only relevant for advanced users who want to increase the IR power even more. This should not be required in ...9 KB (1,582 words) - 09:51, 23 September 2018
- * Advanced users can also make use of the internally accessible ICSP compatible programming ...11 KB (1,864 words) - 11:20, 13 January 2021
- Users can send signals from any PC or server or device that supports CURL, as fol ...18 KB (2,989 words) - 17:15, 12 March 2019